Landspeeder Luke

Hoth - Echo Base Diorama & Bacta Tank

This week's file is the Hoth Echo Base diorama!

For the Bacta Tank I used this clear acrylic tube from Amazon. I also used pieces of a 2021-05-31 01:03:02 +0000 UTC View Post

Crates and Cases (Free sample)

These are a few of the cases included in my latest post, offered here free for non-subscribers.

This is a peek at this week's collection that is available to subscribers:

Yavin 4 Crates, Columns, and Engine

This week's post is this huge collection inspired by the Rogue One promo images on Yavin 4.

Don't forget that you can scale and color these however you want to add some variety! (most crates displayed were printed at 100%)

Engine and stand have been added!

2021-05-22 00:02:48 +0000 UTC View Post

Black Series Mural Box Clips (repost)

If you collect the new Black Series boxes you know that it's a pain in the butt to keep the box art lined up. These clips staggers your boxes at just the right angle so the mural lines up perfectly. They clip together to expand as long as you want! Download link at bottom of post.

2021-05-18 03:18:48 +0000 UTC View Post

Jedi: Fallen Order Crate

Celebrating the release of the new Deluxe Cal Kestis figure with this free Crate file from my J:FO diorama. (reposting this separately so non-patrons can access it).

Shoretrooper Tray

I quickly whipped up this tray and cup for the Shoretrooper to recreate the scene from Mando. The cup is hollowed out and sits on top of the peg in the tray to prevent it from falling off. Tip: set your printer speed to 50mm/s or slower when printing the cup (upside down) to prevent it from knocking over.

2021-05-16 02:56:30 +0000 UTC View Post

AT-AT Leg

I decided to start the weekend early with this HUGE leg of an AT-AT. If you're like me, you don't have room for an entire 1/12 scale walker on your shelf, but this project will allow for some awesome displays and photographs. The joints even work! This was printed on an Ender 3!

2021-05-15 02:21:01 +0000 UTC View Post

Throne of Mandalore

Writing this from the airport as I wait to fly home, but I'm stoked to share this Throne of Mandalore file for this week! And yes it all fits on an Ender 3! As always this is scaled for Black Series figures but set it to 66% for you 3.75" collectors.

You'll need a bit of glue to get this to hold together, and I recommend using a piece of foam core or cardboard on the back to hold the wall pieces in place.

2021-05-09 12:34:37 +0000 UTC View Post

Duel of the Fates

This weekend's post is an updated version of my Duel of the Fates diorama!

The image below is printed on an Ender 5 Plus at a more accurate scale. The circle piece is separate so you can slide it around to better fit your shelf display.

This image below shows the scale when printed on an Ender ...

Black Series / Marvel Legends Mini-Stands

Here is a bonus of these simple stands I designed for my Black Series figures. They are very small and serve to enlarge the foot size of the figure. Make sure you print at 100% infill so the pegs don't break off in the feet. Prints in a multi-pack of 32 (use scissors to separate). Print them in the same color as your shelf! 

Two peg sizes to fit almost all 6" Hasbro figures.

Emperor's Throne Room Display and Black Series Box Stand

This weekend's file is ...

Essential Printing Accessories

I get asked a lot about what I use for my prints, these are the products that I swear by. I will update this list over time as I think of new essentials.

KRYLON Matte Finish  

@Tims_Toyz turned me on to this stuff. This gives a beautiful finish to your prints, will remove shine from the raw filament, ...

Simple Floor Pieces

Some simple floor pieces and a 12" by 12" base that is handy to keep around for photos. Attached below!

Trade Federation Blast Door

I was excited about the new Qui-Gon so I just had to give this a go (at the suggestion of one of the patrons!) This is scaled for Black Series but works with smaller printers (largest edge is 210mm). This thing is huge! Measuring 20.5" wide.

It's separated into many pieces to make painting easier, paint each color group separately before combining for clean edges. I recommend using a finishing spray (I like Krylon Matte) before assembling to avoid scratches.

PRINTING TIPS:

T...

Jedi: Fallen Order

Hope you all have been enjoying all of the bonus files from last week! We ended up with 6 dioramas this week instead of just the 1. 

Next up is this Jedi: Fallen Order diorama with meditation area stencil (best used with spray paint or airbrush).

That loot crate is going to look awesome on your shelf next to the Black Series figures and the upcoming deluxe Cal Kestis figure this summer.

Imperial Arch + Accessories

UPDATE: I've added the computer and crates, paint the computer panels before connecting to the base for cleaner lines. I've also added a complete version of the arch for those of you with larger printers.

Separated for smaller printers!

Obi-Wan Kenobi's Hut

I was too excited not to share this one. All files at the zip file below.

Armorer's Forge

There is an alternate version of the round floor stand and the tube (with no arm) for those of you who won't be printing the larger piece.

Please send me photos of your finished results! 

I printed the flames in clear blue resin and used a string of fairy lights in the bowl. 

Link below!

Death Star Escape Diorama

Death Star Escape inspired diorama.

Print the under-floor panel in red or paint it red, then print the top floor grate in black. The two silver pipes snap into place for easier painting.

Available now for early access members, this upcoming Sunday for everyone else!