All seeing pumpkin ready for download :)
Added 2024-10-02 17:09:27 +0000 UTCTHE ALL SEEING PUMPKIN !!!
Haha , ok this just might be the best halloween prop of 2024 :D
Attached you can see a video of what it looks like "in action" :)
I did mention there are some props in line that will use the functional eye design, so here is another one.
The cool thing is, it's interchangeable from the book, so you don't need to reprint the eye mechanism. You can just add it here , or remove and add to the book :)
There are total of 5 pumpkins to choose from
- 5 lids(top) - version for the motion sensor and version without the
motion sensor
- there is also a non functional version included with 3d printable eyes in case you don't want to mess with electronics, but the electronics version is pretty cool :D
- there is also a "presplit" top part for all 5 pumpkins so you can print the stem in different color
The pumpkins are pretty detailed , i printed mine at 0,2mm layer height but resin prints and 0,12 mm layers will be even more awesome
As always, everything you need to make it work is included :)
Comments
If its all wired corectlly there should be no reason for it not to work, are the seevos working, did xou try a diferent board to make sure its not a faulty one ?
Marko Makaj
2024-11-26 09:08:19 +0000 UTCI just can't get it all to work, got it loaded on the nano, and hooked it all up, and nothing happens, even tried the non motion sensor version, same thing....I have some work to do I guess..
Frederick A Williams
2024-11-25 18:14:07 +0000 UTCFYI: Do not get an ESP32 Nano. The servo library is not compatible. This library only supports boards with an AVR, SAM, SAMD, NRF52 or STM32F4 processor." And don't do like me - get everything soldered up and THEN decide to load the sketch....
CQCoder
2024-10-26 20:38:42 +0000 UTCIs this a video you made and if so where is it located?
darrin tidwell
2024-10-25 21:10:55 +0000 UTCDrop you a message here or somewhere else. I’m a newbie. Also getting error with code when I check it. I’ve used arduino before. I’ll look around and make sure I’m not uploading the code from your word doc wrong. Thanks again for willing to help
darrin tidwell
2024-10-25 21:08:52 +0000 UTCdrop me a message with some vieos/photos, hard to say iwthout knowing if everything else is wired properlly
Marko Makaj
2024-10-25 16:59:30 +0000 UTCcheck the “how to install the code video . however it would apear you did not copy everything right, make sure there are no extra symbols other than the code
Marko Makaj
2024-10-25 16:59:14 +0000 UTCwhen I load the program for sensor, the servos just keep moving, no pause. I made sure to put it somewhere no movement, and servos were not in line of sight of the motion sensor. any ideas?. I really want o use the motion sensor
darrin tidwell
2024-10-24 23:19:18 +0000 UTCNeed a little help please, I'm trying to upload the code to an Arduino and I get the error message 'include' does not name a type'. ??
Nigel Davies
2024-10-23 20:43:21 +0000 UTCFYI The schematic is wrong on this. Eyelid is d6 and eye is d5
Dennis Crawford
2024-10-19 01:23:38 +0000 UTCNope , but you will get s better result if you alightly support the eye opening as the overhangs might get in the wqy if the eyelid. I didnt supprt mine but i slightlly trimmed the opening in post https://www.instagram.com/reel/DAoTTUjKntE/?igsh=NnJkYndjbXI5aDkx
Marko Makaj
2024-10-14 07:04:32 +0000 UTCDoes it need supports?
David Anthony Vernola
2024-10-14 02:13:42 +0000 UTCThis will be my first print of yours. I love moving prints. Can't wait to see what else there is
Dennis Crawford
2024-10-10 12:04:33 +0000 UTCyes, i know :D that is not possible :D i would have to create a new model with your scale in mind, there is no "adjustment" for somethign like that , its not possible :)
Marko Makaj
2024-10-07 13:19:19 +0000 UTCYeah I understand, I would keep the eye and working parts the same, just wanted a bigger pumpkin 🙂
Nigel Davies
2024-10-07 13:18:00 +0000 UTCit is not possible to scale it up when you have parts taht are uncahnged like the eye, and servo's, if you scale everything up the parts will no l onger fit
Marko Makaj
2024-10-07 12:57:05 +0000 UTCI absolutely love this and have already made one. But I was wondering if you could make a larger version? I would usually resize models myself but I don't know anything about 3D modelling so wouldn't be able to change the eye hole to keep it the correct size
Nigel Davies
2024-10-07 07:59:38 +0000 UTCI'm in the UK, it came to about £30 the Arduino was the most expensive part
Nigel Davies
2024-10-07 07:58:19 +0000 UTChas anyone in US priced about what all the electronics/parts would total?
Steve Burk
2024-10-04 00:54:39 +0000 UTCAwesome!!!!
David Anthony Vernola
2024-10-03 21:51:55 +0000 UTCDefinately not, ill juat mix it uo between other projects but i have quite a few things planned :)
Marko Makaj
2024-10-03 21:31:33 +0000 UTCThis and book are so very awesome. I hope this pumpkin is not the last use of the eye mech. Hoping for more uses.
David Anthony Vernola
2024-10-03 15:45:34 +0000 UTCyes, as its shown in the video :)
Marko Makaj
2024-10-03 13:53:19 +0000 UTCor better yet, do you glue down Box 1 B into the frame, because there is nothing that holds the eye in.
Brian olson
2024-10-03 13:51:41 +0000 UTCboy 1B goes onto box 1A,, i named them so its suggested that way - Box 1 ( A and B) , asame as for the eye - eye 1 (A and B) . there is also an assembly video in the folder that shows you how to put the eye toegether step by step , its in the "build guide and code" folder :)
Marko Makaj
2024-10-03 13:51:13 +0000 UTCJust printed everything and got the electronics ready bt the diagram to put the eye mech together seems a big confusing. There are parts that arent shown where they go, like Box 1. B, eye 1.b
Brian olson
2024-10-03 12:57:49 +0000 UTC😁😁😁
Marko Makaj
2024-10-02 22:10:01 +0000 UTCHaha true :D appreciate it : d
Marko Makaj
2024-10-02 22:09:54 +0000 UTCThank you :)
Marko Makaj
2024-10-02 22:09:43 +0000 UTCHaha :D
Marko Makaj
2024-10-02 22:09:38 +0000 UTCHmm :)
Marko Makaj
2024-10-02 22:09:33 +0000 UTCEasy if you carve it out its juat a matter of positioning the eye
Marko Makaj
2024-10-02 22:09:26 +0000 UTCIll post a video (moat likely tomorow) that explains it all :)
Marko Makaj
2024-10-02 22:08:59 +0000 UTCUnfortinatelly no, it will not dit the mechanism
Marko Makaj
2024-10-02 22:08:39 +0000 UTCHappy to hear :)
Marko Makaj
2024-10-02 22:08:26 +0000 UTCJust awesome, Marko! [sigh] I knew ordering electronics to build only two all-seeing eye projects for Halloween was not enough. Second order coming up...
Ed_F
2024-10-02 21:32:19 +0000 UTCIsn't the 22mm eye also good? Because in Italy there is a risk that it won't arrive by the end of the month
Samuel Incani
2024-10-02 18:02:36 +0000 UTCnever done anything with a arudino. i dont see a tutorial on how to load the code and stuff. also, how easy would it be to install the eye into a real pumpkin?
Bradley r Schultz
2024-10-02 18:00:32 +0000 UTCWould love to see your take on a wearable creepy pumpkin head
Andy Hughes
2024-10-02 17:31:15 +0000 UTCNo freaking way!!?!?!!
Andrew Sheffield
2024-10-02 17:23:19 +0000 UTCAwesome!
David Anthony Vernola
2024-10-02 17:22:16 +0000 UTCThis is creepy AF, I love it ahahah
Damien Moreau
2024-10-02 17:12:05 +0000 UTCYeeeees! 😎
PiraLoco
2024-10-02 17:11:20 +0000 UTC
