XaiJu
lastswordminiatures
lastswordminiatures

patreon


June

Few surprises this month. You already know all the miniatures.

We have made a considerable effort to increase the number of them. Our team is going from 2 to 3 sculptors. 

Jason will be working on the Warriors of the Ashes and Vampires ranges that you will be seeing in the coming months. Mario will continue with the Human Kingdoms and High Elves. 

Stephan will continue to finish the lizardmen while supporting us with the monsters. This month's Griffin is his own work.

I think this puts us among the Patreons with the highest quality and variety at the same time.

I anticipate the question you will ask me.  As usual the files will be released around the 15th. It may be earlier or later depending on the weekend. Right now there is a lot to test and suport.

As always, thank you very much and remember, our continued growth depends on you protecting the files. We are 5 people dreaming of bringing you dozens of new miniatures, and although it seems a lot, 400 patrons is just the beginning.

Thank you all for your support.

Files: https://www.patreon.com/posts/files-again-52617255


Pocas sorpresas este mes. Ya conoces todas las miniaturas.

Hemos hecho un esfuerzo considerable para aumentar el número de ellas. Nuestro equipo pasa de 2 a 3 escultores.

Jason trabajará en las gamas de Guerreros de las Cenizas y Vampiros que veréis en los próximos meses. Mario continuará con los Reinos Humanos y los Altos Elfos.

Stephan seguirá terminando los hombres lagarto mientras nos apoya con los monstruos. El Grifo de este mes es obra suya.

Creo que esto nos sitúa entre los Patreons con mayor calidad y variedad al mismo tiempo.

Me anticipo a la pregunta que me haréis.  Como es habitual, los archivos se publicarán alrededor del día 15. Puede ser antes o después dependiendo del fin de semana. Ahora mismo hay mucho que probar y soportar.

Como siempre, muchas gracias y recuerda que nuestro crecimiento continuo depende de que protejas los archivos. Somos 5 personas soñando con traeros decenas de nuevas miniaturas y aunque parezca mucho, 400 mecenas es sólo el principio.

Gracias a todos por vuestro apoyo.

Archivos:  https://www.patreon.com/posts/files-again-52617255

June June June June June June June June June June June June June June June June June

Comments

Hi Icarus. I'm sorry, but no. If you enter on the first day, you know that there is a possibility that it is not updated. But in our case, the images indicate the month to which the new item belongs, and also you have all the publications open. It is very easy in our case, dedicating a minimum of time to know to which month belongs each reference. The only thing I can do is to give you your money back if you ask me before the links are made public. But by private message please. Best regards

Last Sword Miniatures

Are we still able to get these files as patrons as they are what's being advertised before signing up?

Anto - Icarus Games

not to mention the incredible skill of your painter

Riathenors

Where can I find the download for the Reichsguard Knights?

Jan-Ole Kliem

Hi Lastsword Miniatures, can you please switch to lychee for your presupported files? As some of the other patrons above have mention as well, Im having consistent trouble printing the files due to the thin supports and would like the ability to adjust some of them.

KingK

We have just published them again. Dropbox collapsed yesterday.

Last Sword Miniatures

Have the files been released yet?

Martin Brodigan

Hello Mark. I was very glad to see your subscription the other day. Welcome. In principle it shouldn't be a problem that you printed all the parts at once. We have done it in the tests. I printed 6 to make sure it worked. When the supports break it is that it does not have the strength to hold the miniature. In this case we know it does because it is tested. Try with a single piece to go up the exposure half a second to make sure that the resin is well cured. If everything is normal with 1 second or a second and a half it should hold without problems. If it is not enough we would have to replace 4 or 5 supports at the points where the construction starts with thicker ones. But I don't think you will need it. The supports we started with thicker supports and in less quantity. But several Patrons suggested this change. If many Patrons have this problem we can go back to the previous one or look for something hybrid. It is difficult to find a system that works for everyone.

Last Sword Miniatures

first print attempt failed on griffon. I have an Epax E10 so was able to put the all parts on the plate. Starting it before bed I woke up to empty supports and mounding puddles on the fep. I noticed really thin support attachment points on this months models. It appears the weight of parts just broke away from the supports. Now since i had alot of models on the plate the overall suction on fep might have cause alot of release stress so i will try to print one or two parts by themselves to see if these thin supports can still work. Otherwise I will need to work on my own skills setting up supports unless of course others have similiar issues and an update is sent out. Thanks

Mark Detlor

The idea is to have everything on our website. But sometimes we are slower than we would like to be.

Last Sword Miniatures

I am really torn between two units. Do the others end up on the MMF for purchase?

Highlander

Well, I'm missing a silly base that we had forgotten to design. The sculptor is working on it right now. As soon as I finish it I will upload everything. Tonight at the end of the night or tomorrow morning.

Last Sword Miniatures

When is the download going to be available for June?

Jefferson Thacker

My fingers are ready to push download lol

Jon Letham

In this case it was a paractical issue. 50*50 didn't need anything more than the stone, and 100*50 was more complicated to decorate. So it works in all sizes without much problem.

Last Sword Miniatures

expect 50x100 to be the norm in the future or if a 50x50 remains it is somehow weaker/small than todays stats.

Mark Detlor

The stone that holds the griffin is separated. it only needs to cut the plug to be placed on a 50x50 base.

Last Sword Miniatures

The Griffon does not seem to fit on a 50x50mm base for the ninth age, is it possible to cut the base off at some point and still have it look good?

Joost Veenstra

For those of you who have partial rewards, we will send you a private message asking once the files are ready.Normally around the 15th

Last Sword Miniatures

How do we get the link for the files? Do we have to say which faction we want?

Keg and Krow

Gracias por el enorme curro. Es un gustazo ver el trabajo y la ilusión.

R.C.

Aren’t they already?

Blair Fenning

AMAZING 👏

Christian Natello

At how many patrons will you consider pre-supported?

István Végh

Glad to be here for my second month, very exciting stuff that I'm seeing.

Andrew Pryor

This month is amazing! Just like the previous ones ;)

Mikkelangelo Kers

Awesome news! Love to see you guys doing well. You deserve it!

Patrick

Because of you, I bought a new printer! Waiting, waiting, waiting. :) You are great!

Evgeniy Efimenko

I am amazed! Fantastic work!

Tonny

Amazing work, looking forward to vampires!

Scott Woods

I would have to agree, quality here is top notch!

Ne Obliviscaris

Great to hear that the team is expanding and that more Lizards are on the way :)

Overread


More Creators